NITRATION OF BENZENE AND METHYLBENZENE
This page looks at the facts about the nitration of benzene and
methylbenzene. The mechanisms for these reactions are covered elsewhere
on the site, and you will find links to these. The nitration of benzene Nitration happens when one (or more) of the hydrogen atoms on the benzene ring is replaced by a nitro group, NO2. Benzene is treated with a mixture of concentrated nitric acid and concentrated sulphuric acid at a temperature not exceeding 50°C. The mixture is held at this temperature for about half an hour. Yellow oily nitrobenzene is formed. You could write this in a more condensed form as: The concentrated sulphuric acid is acting as a catalyst and so isn't written into the equations. At higher temperatures there is a greater chance of getting more than one nitro group substituted onto the ring. You will get a certain amount of 1,3-dinitrobenzene formed even at 50°C. Some of the nitrobenzene formed reacts with the nitrating mixture of concentrated acids. Notice that the new nitro group goes into the 3 position on the ring. Nitro groups "direct" new groups into the 3 and 5 positions. The reasons for this "directing effect" are beyond UK A level. | |
Note: The numbering on the ring goes clockwise around the ring starting with number 1 at the top. | |
It is also possible to get a third nitro group attached to the ring
(in the 5 position). However, nitro groups make the ring much less
reactive than the original benzene ring. Two nitro groups on the ring
make its reactions so slow that virtually no trinitrobenzene is produced
under these conditions. | |
Note: Follow this link if you want the mechanism for the nitration of benzene. You will find the mechanism for the nitration of nitrobenzene (the reaction producing 1,3-dinitrobenzene) at the bottom of the page you will get to by following this second link. If you choose to follow either of these links, use the BACK button (or the HISTORY file or GO menu) on your browser to return to this page later. | |
The nitration of methylbenzene (toluene)
Methylbenzene reacts rather faster than benzene - in nitration, the
reaction is about 25 times faster. That means that you would use a
lower temperature to prevent more than one nitro group being substituted
- in this case, 30°C rather than 50°C. Apart from that, the reaction
is just the same - using the same nitrating mixture of concentrated
sulphuric and nitric acids. You get a mixture of mainly two isomers formed: 2-nitromethylbenzene and 4-nitromethylbenzene. Only about 5% of the product is 3-nitromethylbenzene. Methyl groups are said to be 2,4-directing. For 2-nitromethylbenzene: . . . and for 4-nitromethylbenzene: | |
Note: You will find the mechanism for the nitration of methylbenzene by following this link. Use the BACK button (or HISTORY file or GO menu) on your browser to return to this page later. | |
Just as with benzene, you will get a certain amount of dinitro
compound formed under the conditions of the reaction, but virtually no
trinitro product because the reactivity of the ring decreases for
every nitro group added. From an experimental point of view this is
just as well. Trinitromethylbenzene used to be called trinitrotoluene
or TNT! The reason for the 2,4-directing effect of the methyl group is beyond UK A level, but the increased reaction rate can be explained up to a point. The reactivity of a benzene ring is governed by the electron density around the ring. Methyl groups tend to "push" electrons towards the ring - increasing the density, and so making the ring more attractive to attacking reagents. This is actually a simplification. In order to understand the rate effect properly you have to think about the stability of the intermediate ions formed during the reactions, because this affects the activation energy of the reactions. This is also the basis for the directing effect and is again beyond UK A level. | |
Warning! I have deliberately chosen not to use the strict IUPAC names for the compounds in this section, because I see them as illogical and inconsistent with the older names for these compounds. The names for the compounds with one nitro group substituted into methylbenzene should be methyl-2-nitrobenzene and methyl-4-nitrobenzene. The reason for these names is that you should strictly name the attached groups in alphabetical order. It seems to me to be illogical on three counts. Firstly, it breaks up the name of the hydrocarbon, so that it is no longer immediately obvious that you are talking about a derivative of methylbenzene. Secondly, it doesn't relate to the older names for these compounds. Methyl-4-nitrobenzene, for example, used to be called para-nitrotoluene. The "para" refers to the 4 position. You could equally have called it 4-nitrotoluene. My name of 4-nitromethylbenzene is a direct translation of this. I think that's entirely logical! Thirdly, you can end up with completely different names for compounds which are structurally similar. For example, if you think about substituting chlorines into these positions instead of nitro groups you will have to completely change the names for purely alphabetical reasons. That's silly! I may well be in a minority of one on this, but I am sticking to my guns on it. In fact, IUPAC is much more flexible about these things than they are sometimes given credit for. I doubt if it would worry them, although it might upset your teachers or lecturers. Obviously, if you are working in a system which still calls methylbenzene "toluene", none of this bothers you! |
Tuesday, 1 October 2013
NITRATION OF BENZENE AND METHYLBENZENE
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment